EKOPLAST 50
APPLICATION: Use on solid backing of Concrete, Cement Block, Brick, Drywall, Exterior/ Interior Plasterboard OSB, Steel Structures and many other substrata. By using trowel or pump spray. Ambient temperature to be between 45 F ( 7C) – 100 F ( 38 C). Keep hydrated for day or two depending on weather conditions
SURFACE PREPARATION: Surfaces must be structurally sound, clean, dry and free of dust, dirt or other contaminants impairing bond. Prepare surface to be smooth and free of cracks, hoIes and voids.
PRIME: In case surface needs priming Kemset recommends Kemset Coarse Primer to achieve best results. Apply over the prepared surface, and allow Kemset Coarse Primer to dry 12 hours before applying EkoPlast-50.
Other brands of primers can be used also as long as they provide coarse surface.
- Speed: 750 RPM
- Power Source: Cordless-Electric
- Battery Cell Type: Lithium
- Voltage: 20 Volts
- Battery Capacity: 2 Ah
Use on solid backing of Concrete, Cement Block, Brick, Drywall, Exterior/ Interior Plasterboard OSB, Steel Structures and many other substrata. By using trowel or pump spray. Ambient temperature to be between 45 F ( 7C) - 100 F ( 38 C). Keep hydrated for day or two depending on weather conditions
Surfaces must be structurally sound, clean, dry and free of dust, dirt or other contaminants impairing bond. Prepare surface to be smooth and free of cracks, hoIes and voids.
Apply generous amount of Kemset Coarse Primerover the prepared surface, and allow Kemset Coarse Primer to dry 12 hours before applying EkoPlast-50.
Control joints: To reduce the potential shrinkage cracking limit the size of wall panels to 144 sqft (14 m2).
Expansion Joints: Use as needed when there is a change in substrates, inside corners to prevent potential cracking due to changing intemperatures.
Corner Beads: To be used all outside edges to protect the exposed stucco and provide clean finish lines.
Water resistant building paper, firim accessories, Weep screeds, Cosing beads, Galvanized expanded metal lath, Galvanized nails and staples where necessary.
Each coat EkoPlast-50 can be applied up to 2,5 cm (1 inch) thickness. For best result apply in multiple costs and allow at least 2 hours drying between coats, depending on weather conditions. Fiber mesh can be used between coats for extra strenght if desired.
Mix 20 Kg (44 lb) of EkoPlast-50 with 3 gallons (11.5 liters) of water for 6-8 minutes using low speed mixer until the mixture reaches a smooth trowable consistency. Add more water if necessary. Working time is about 2 hours depending on weather conditions.
Use screeds where necessary to adjust thickness. When mortar cures to touchable condition, skim coat/trowel for even flat finish. Wait 48-72 hours until the mortar completely dries before painting. Depending on weather conditions and thickness of the application.
COVERAGE: 20 Kg (44 lb) bag:
1 cm (3/8 inch) thick approx: 4.7 m2 (51 sqft)
2 cm (3/4 inch) thick approx: 2.35 m2 (26 sqft)
2,5 cm (1 inch) thrick approx: 1.9 m2 (20 sqft)
STORAGE CONDITIONS: Store EkoPlast-50 indoors at temperatures above 5 C (40 F) in clean dry environment.
EKOPLAST 50
LIGHTWEIGHT/MICROGLASS/POLYMER MODIFIED
EKOPLAST 50
Thermal Insulation Plaster
Technical Specifications:
ISO 9001: 2015, ISO 14001 2015 TCS CERT
CE EN 998-1
Apperance: White powder
Dry density: 450 (+/-) 50 Kg/m3
Thermal conductivity: t1< 0.1 – 0.065 W/mK
Compressive strenght: CSII > 1.4 N/mm2
Bond strenght: >0.3 N/mm2
Water absorbtion: W1 0.25 kg/m2. min 0.5
Water vapor permeabilty: 3,49ɥ
Fire resistance: Class 1A Fireproof
WARNING – HAZARDOUS
MAY CAUSE IRRITATION
RISK: May cause respiratory, skin and eye irritation.
SAFETY: Avoid contact with the eyes and skin. Avoid inhaling the vapors and wear suitable protective clothing covering the skin including eye protection, gloves and suitable respirators. Keep out of the reach of children.
FIRST AID: Flush eyes and wash skin thoroughly with clean water. If inhales, vacate are a immediately. Seek medical attention if irritation persists. If swallowed do not induce vomiting. Drink plenty of clean water and seek medical attention immediately.
SPILLS / LEAKS: Maintain work area and keep it clean. Keep out of sewers and storm drainage.
DISPOSAL: Follow above safety indtructions and collect in disposal containers in accordance to local disposal requirements.
MANUAL HANDLING: The manual handling of this product without due care and attention could result in physical injury. Wear back supports and use team lifting when manual lifting is required. Follow OSHA recommendations.
ADDITIONAL INFORMANTION/UPDATES: Updated Material Safaty Data Sheet (MSDS) and Product Data Sheet (PDS) are available at KEMSET.COM
WARRANTY: KEMSET USA warrants this product to be of merchantable quality when used or applied inaccordance with the instructions herein. The product is not warrented as suitable for any purpose or use other than the general purpose for which it is intended. Liability under this warranty is limited to the replacement of product found to defective as purchased. In the event of a claim under this warranty, notice must be given to KEMSET USA in writing. This limited warranty is issued and acceptes in lieu of other express warranties and expressly excludes liablity for consequential damages.
WARNING: This product contains impurities known to the State of California to cause cancer and/or birth defects or other repoductive harm.
Keep out of the reach of children.
Reviews
There are no reviews yet. Be the first to review “THERMOPAINT” Your email address will not be published. Required fields are marked *
Your Rating:*
Download Product Details
Material Safety Data Sheets
Copyright © 2023 www.kemset.com - All Rights Reserved Designed & Developed By WEB & MARKETING EXPERTS LLC