ELASTICOTE 500
$ 226
$ 283


ElastiPol 3500 Two Component is low viscosity, solvent-free, two components, self-leveling, multi-purpose polyurethane based coating and waterproofing.

 

FIELD OF APPLICATION:

-Interior and exterior use

-On concrete and cement based mineral surfaces

-Waterproofing membrane for Roofs, Decks, Ponds and underground water storage.

 

FEATURES:

Low viscosity

High bond strength

Solvent free, excellent penetration and adhesion ability

  • Speed: 750 RPM
  • Power Source: Cordless-Electric
  • Battery Cell Type: Lithium
  • Voltage: 20 Volts
  • Battery Capacity: 2 Ah
Availability: In Stock
  • Category: Elastic Coatings

Part A: 16 kg.net Part B: 4 kg.net Total: Part A+B: 20 kg

Store in original sealed containers in a cool dry environment at temperatures between +5°C and +30°C. Do not put excessive loads on top of the products, which would damage the packaging.

Minimum 12 months for part A and 9 months for part B from date of production if stored in original unopened containers. Once opened, product should be used within one week.

Ambient and product temperatures are must be between +15°C and +25°C before mixing. Prior to mixing, stir part A and B separately with a mechanical drill and paddle at a very low speed. Add component B gradually into component A and mix appoximently 3 minutes untill you reach a homogeneous consistency. If necessary, after mixing desired aggregate is added to the mixture and stirred again until a homogeneous mixture is obtained. Pour the contents into a clean container and mix for another couple minutes.

PRIME SURFACES BEFORE APPLICATIONS USING KEMPRİME 2000

 

WHEN EXPOSED TO DİRECT SUN USE ELASTIPOL 3600 UV TOP COAT FOR UV PROTECTİON.

Avoid application under excessive heat, wind, rain and/or when the ambient and/or substrate temperature is below +10°C or above +30°C. In cold conditions, heaters should be used to increase the ambient temperature an workability of the product. After the mixing procedure, ElastiPol 3500 is poured and spread eventy using serrated trowel. After spreading the material evenly, roll immediately in two directions with a spiked roller to ensure even thickness. Make sure that a continuous coat covers the substrate. If heating is required, use only electric powered warm air blower system. Mixed product should be applied in within 30 minutes. Waiting time between coats should be minimum 10 hours in +20°C and maximum 48 hours. If 48 hours pass and another coat is needed surface should be sanded. The product would be completely cured in minimum 7 days to reach its maximum mechanical and chemical resistance. Reaction times of resin based systems depends on ambient and substrate temperatures as well as relative humidity. Under lower temperatures reaction times are longer which increases pot life, coating intervals and working time. High temperatures contact with water for a minimum of 24 hours. Within this period, contact with water can cause a surface carbonation and/or surface tackiness. In such cases, overall coating should be removed from the floor and renewed.

Surface must be regularly cleaned using rotary brush, mechanical scrubbers, scrubber dryer, high pressure washer, wash and vacuum techniques etc. Using detergents and waxes. Any spillages must be removed immediately.

Clean all tools and application equipment with thinner immediately afet use. Hardened/cures material can only be mechanically removed.

 

EKOPLAST 3500

 

WARNING – HAZARDOUS

MAY COUSE IRRITATION

RISK:May cause respiratory, skin and eye irritation.

SAFETY: Avoid contact with the eye and skin. Avoid inhaling the vapors and wear suitable protective clothing covering the skin including eye protection, gloves and suitable respirators. Keep out of the reach of children.

FIRST AID: Flush eyes and wash skin thoroughly with clean water. If inhaled, vacate area immediately. Seek medical attention if irritation persists. If swallowed do not induce vomiting. Drink plenty of clean water and seek medical attention immediately.


SPILLS LEAKS: Maintain work area and keep it clean. Keep out of sewers and storm drainage.


DISPOSAL: Follow above safety instructions and collect in disposal containers in accordance to local disposal requirements.


MANUAL HANDLING: The manual handling of this product without due care and attention could result in physical injury. Wear back supports and use team lifting when manual lifting is required. Follow all OSHA recommendations.


ADDITIONAL INFORMATION/UPDATES: Updates Material Safety Data Sheet (MSDS) and Product Data Sheet (PDS) are available at KEMSET.COM


WARRANTY: KEMSET USA warrants this product to be of merchantable quality when used or applied in accordance with the instructions herein. The product is not warranted as suitable for any purpose or use other than the general purpose for which it is intended. Liability under this warranty is limited to the replacement of the product found to defective as purchased. In the event of a claim under this warranty, notice must be given to KEMSET USA in writing. This limited warranty is issued and accepted in lieu of other express warranties and expressly excludes liability for consequential damages.

WARNING: This product contains impurities known to the State of California to cause cancer and/or birth defects or other repoductive harm.

Keep out of the reach of children.

Reviews

There are no reviews yet. Be the first to review “THERMOPAINT” Your email address will not be published. Required fields are marked *

Your Rating:*

Save my name, email, and website in this browser for the next time I comment.